Problem:
I have a brand new BROTHER HL-3045CN LED Laser Printer (Colour), and very carefully assembled it (Have photos of the process!), and set it up as per instructions. The TEST PAGE printed perfectly. I then set up as best I could, the LINUX drivers, and connected it to the computer.
I am using UE3.4 lite (64bit) {UBUNTU 12.04LTS?} on a brand new ASUS computer!
The printer was 'found' by the computer and set up. It recognised the printer as being 'idle' and the printer was 'ready'.
BUT when a test print was tried, the computer came back with the error message “waiting for the printer to respond” it waited 9hours!!!
I have since removed the printer from the computer and re-installed the drivers etc., all to no avail.
I have virtually NO knowledge of using the Terminal, so am wondering if there is something that needs to be done in the Operating system?
Detailed instructions would be appreciated.
ps, just had a thought, Ultimate Edition uses Gnome - is this the problem?
Peter AB
Are you a spammer
Please note, that the first 3 posts you make, will need to be approved by a forum Administrator or Moderator before they are publicly viewable.
Each application to join this forum is checked at the Stop Forum Spam website. If the email or IP address appears there when checked, you will not be allowed to join this forum.
If you get past this check and post spam on this forum, your posts will be immediately deleted and your account inactivated.You will then be banned and your IP will be submitted to your ISP, notifying them of your spamming. So your spam links will only be seen for an hour or two at most. In other words, don't waste your time and ours.
This forum is for the use and enjoyment of the members and visitors looking to learn about and share information regarding the topics listed. It is not a free-for-all advertising venue. Your time would be better spent pursuing legitimate avenues of promoting your websites.
Please note, that the first 3 posts you make, will need to be approved by a forum Administrator or Moderator before they are publicly viewable.
Each application to join this forum is checked at the Stop Forum Spam website. If the email or IP address appears there when checked, you will not be allowed to join this forum.
If you get past this check and post spam on this forum, your posts will be immediately deleted and your account inactivated.You will then be banned and your IP will be submitted to your ISP, notifying them of your spamming. So your spam links will only be seen for an hour or two at most. In other words, don't waste your time and ours.
This forum is for the use and enjoyment of the members and visitors looking to learn about and share information regarding the topics listed. It is not a free-for-all advertising venue. Your time would be better spent pursuing legitimate avenues of promoting your websites.
Brother laser (colour) printer on UE3.4lite[SOLVED]
4 posts
• Page 1 of 1
Brother laser (colour) printer on UE3.4lite[SOLVED]
by pab001 » Tue Jun 04, 2013 8:18 pm
- pab001
- U.E. Newbie
- Posts: 6
- Joined: Mon Dec 28, 2009 5:54 am
- Operating System: Ultimate Edition 3.4 64 BIT
Re: Brother laser (colour) printer on UE3.4lite
by ryanvade » Tue Jun 04, 2013 9:36 pm
i5 2450m Pentium D 960 @ 4 GHz
6 GB ram 2 GB ram
Intel HD 3000 Graphics / Nvidia GT 630M Nvidia GT 520 @ 820 MHz
Diamond II-B 3.10-rc4/Windows 7 Home Premium KDE | Windows 7 Starter/Arch Linux
-
ryanvade - Moderator
- Posts: 499
- Joined: Sat Apr 28, 2012 10:54 am
- Operating System: Other Linux
Re: Brother laser (colour) printer on UE3.4lite
by pab001 » Tue Jun 04, 2013 11:47 pm
Ryanvade in answer to your question, I Downloaded them from the BROTHER site:
http://welcome.solutions.brother.com/bs ... #HL-3045CN etc
Peter.
http://welcome.solutions.brother.com/bs ... #HL-3045CN etc
Peter.
- pab001
- U.E. Newbie
- Posts: 6
- Joined: Mon Dec 28, 2009 5:54 am
- Operating System: Ultimate Edition 3.4 64 BIT
Re: Brother laser (colour) printer on UE3.4lite
by pab001 » Wed Aug 28, 2013 11:30 pm
SOLVED.
I am not certain how, it was done by my Grandson!He said that a 'tiddle' (~)? was incorrect in one of the instructions! ? I could not cut and paste at the time, so it was probably my faulty typing!!
I am not certain how, it was done by my Grandson!He said that a 'tiddle' (~)? was incorrect in one of the instructions! ? I could not cut and paste at the time, so it was probably my faulty typing!!
- pab001
- U.E. Newbie
- Posts: 6
- Joined: Mon Dec 28, 2009 5:54 am
- Operating System: Ultimate Edition 3.4 64 BIT
4 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 5 guests