Ok Admin I tried to update flash player thru synaptic but got a crash report that says
Sorry ,the package "linux-backports-modules-wireless-2.6.32-22-generic-pae 2.6.32-22.13'' failed to install or upgrade the etho stuff I had already done .It was set to auto for everyone.Now after the failed attempt at downloading the flash player updates the wireless wont even connect to the internet after a reboot.
Ok I did something hooked it into the wired connection then connected to Mozilla then turned on wireless it stayed connected for about 5min before it crashed.That was with the wired disconnected.Its like something conflicting with the wireless.
Did a dmesg outcome below
[ 0.204564] system 00:03: ioport range 0x290-0x297 has been reserved
[ 0.204567] system 00:03: ioport range 0x880-0x88f has been reserved
[ 0.239384] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.239389] pci 0000:00:01.0: IO window: 0xb000-0xbfff
[ 0.239396] pci 0000:00:01.0: MEM window: 0xfb000000-0xfcffffff
[ 0.239402] pci 0000:00:01.0: PREFETCH window: 0xe0000000-0xefffffff
[ 0.239423] pci 0000:00:01.0: setting latency timer to 64
[ 0.239429] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.239433] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.239436] pci_bus 0000:01: resource 0 io: [0xb000-0xbfff]
[ 0.239439] pci_bus 0000:01: resource 1 mem: [0xfb000000-0xfcffffff]
[ 0.239442] pci_bus 0000:01: resource 2 pref mem [0xe0000000-0xefffffff]
[ 0.239497] NET: Registered protocol family 2
[ 0.239630] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.240161] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.241465] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.242179] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.242186] TCP reno registered
[ 0.242375] NET: Registered protocol family 1
[ 0.242427] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[ 1.840013] pci 0000:00:10.4: EHCI: BIOS handoff failed (BIOS bug?) 01010001
[ 1.840030] pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message
[ 1.840048] pci 0000:01:00.0: Boot video device
[ 1.840303] cpufreq-nforce2: No nForce2 chipset.
[ 1.840345] Scanning for low memory corruption every 60 seconds
[ 1.840521] audit: initializing netlink socket (disabled)
[ 1.840549] type=2000 audit(1281564659.840:1): initialized
[ 1.849666] Trying to unpack rootfs image as initramfs...
[ 1.860751] highmem bounce pool size: 64 pages
[ 1.860761] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.868097] VFS: Disk quotas dquot_6.5.2
[ 1.868234] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.869117] fuse init (API version 7.13)
[ 1.869285] msgmni has been set to 1682
[ 1.869695] alg: No test for stdrng (krng)
[ 1.869814] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.869819] io scheduler noop registered
[ 1.869821] io scheduler anticipatory registered
[ 1.869824] io scheduler deadline registered
[ 1.869878] io scheduler cfq registered (default)
[ 1.870057] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.870091] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.870228] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 1.870234] ACPI: Power Button [PWRB]
[ 1.870300] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[ 1.870310] ACPI: Sleep Button [SLPB]
[ 1.870391] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 1.870395] ACPI: Power Button [PWRF]
[ 1.870470] fan PNP0C0B:00: registered as cooling_device0
[ 1.870480] ACPI: Fan [FAN] (on)
[ 1.870902] processor LNXCPU:00: registered as cooling_device1
[ 1.880682] thermal LNXTHERM:01: registered as thermal_zone0
[ 1.880700] ACPI: Thermal Zone [THRM] (47 C)
[ 1.888533] isapnp: Scanning for PnP cards...
[ 1.894422] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.894554] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.895132] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.896713] brd: module loaded
[ 1.897436] loop: module loaded
[ 1.897645] input: Macintosh mouse button emulation as /devices/virtual/input/input3
[ 1.898297] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[ 1.898306] alloc irq_desc for 20 on node -1
[ 1.898309] alloc kstat_irqs on node -1
[ 1.898319] pata_acpi 0000:00:0f.0: PCI INT B -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20
[ 1.898404] pata_acpi 0000:00:0f.0: PCI INT B disabled
[ 1.898442] pata_acpi 0000:00:0f.1: PCI INT A -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20
[ 1.898478] pata_acpi 0000:00:0f.1: PCI INT A disabled
[ 1.898920] Fixed MDIO Bus: probed
[ 1.898976] PPP generic driver version 2.4.2
[ 1.899091] tun: Universal TUN/TAP device driver, 1.6
[ 1.899094] tun: (C) 1999-2004 Max Krasnyansky <
[email protected]>
[ 1.899263] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.899640] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
[ 1.899648] alloc irq_desc for 21 on node -1
[ 1.899651] alloc kstat_irqs on node -1
[ 1.899661] ehci_hcd 0000:00:10.4: PCI INT C -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 1.899690] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 1.899788] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
[ 1.899879] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfdffe000
[ 1.947863] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00
[ 1.948118] usb usb1: configuration #1 chosen from 1 choice
[ 1.948166] hub 1-0:1.0: USB hub found
[ 1.948183] hub 1-0:1.0: 8 ports detected
[ 1.948274] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.948303] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.948379] uhci_hcd 0000:00:10.0: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 1.948396] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 1.948497] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
[ 1.948531] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000dc00
[ 1.948693] usb usb2: configuration #1 chosen from 1 choice
[ 1.948735] hub 2-0:1.0: USB hub found
[ 1.948750] hub 2-0:1.0: 2 ports detected
[ 1.948829] uhci_hcd 0000:00:10.1: PCI INT A -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 1.948842] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 1.948924] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 1.948960] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000d800
[ 1.949113] usb usb3: configuration #1 chosen from 1 choice
[ 1.949154] hub 3-0:1.0: USB hub found
[ 1.949168] hub 3-0:1.0: 2 ports detected
[ 1.949240] uhci_hcd 0000:00:10.2: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 1.949253] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 1.949351] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 1.949387] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000d400
[ 1.949563] usb usb4: configuration #1 chosen from 1 choice
[ 1.949604] hub 4-0:1.0: USB hub found
[ 1.949620] hub 4-0:1.0: 2 ports detected
[ 1.949699] uhci_hcd 0000:00:10.3: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 1.949713] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 1.949792] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 1.949827] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000d000
[ 1.949989] usb usb5: configuration #1 chosen from 1 choice
[ 1.950032] hub 5-0:1.0: USB hub found
[ 1.950047] hub 5-0:1.0: 2 ports detected
[ 1.950182] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.950185] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.950405] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.956549] mice: PS/2 mouse device common for all mice
[ 1.956816] rtc_cmos 00:05: RTC can wake from S4
[ 1.956917] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.956979] rtc0: alarms up to one year, y3k, 242 bytes nvram
[ 1.957155] device-mapper: uevent: version 1.0.3
[ 1.957400] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised:
[email protected][ 1.957528] device-mapper: multipath: version 1.1.0 loaded
[ 1.957534] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.957772] EISA: Probing bus 0 at eisa.0
[ 1.957821] EISA: Detected 0 cards.
[ 1.960032] cpuidle: using governor ladder
[ 1.960037] cpuidle: using governor menu
[ 1.960615] TCP cubic registered
[ 1.960794] NET: Registered protocol family 10
[ 1.961416] lo: Disabled Privacy Extensions
[ 1.961835] NET: Registered protocol family 17
[ 1.961943] Using IPI No-Shortcut mode
[ 1.962135] PM: Resume from disk failed.
[ 1.962157] registered taskstats version 1
[ 1.962480] Magic number: 6:788:198
[ 1.962620] rtc_cmos 00:05: setting system clock to 2010-08-11 22:11:00 UTC (1281564660)
[ 1.962626] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.962629] EDD information not available.
[ 1.984569] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 2.304067] usb 1-3: new high speed USB device using ehci_hcd and address 2
[ 2.517840] usb 1-3: configuration #1 chosen from 1 choice
[ 2.563275] isapnp: No Plug & Play device found
[ 2.672857] Freeing initrd memory: 13392k freed
[ 2.693143] usb 1-6: new high speed USB device using ehci_hcd and address 3
[ 2.693219] Freeing unused kernel memory: 676k freed
[ 2.694319] Write protecting the kernel text: 4836k
[ 2.694377] Write protecting the kernel read-only data: 1880k
[ 2.771203] ramzswap: disk size set to 1030120 kB
[ 2.786818] udev: starting version 151
[ 2.825639] usb 1-6: configuration #1 chosen from 1 choice
[ 2.914435] Adding 1030116k swap on /dev/ramzswap0. Priority:100 extents:1 across:1030116k SS
[ 2.918882] Initializing USB Mass Storage driver...
[ 2.938744] scsi0 : SCSI emulation for USB Mass Storage devices
[ 2.972670] usbcore: registered new interface driver usb-storage
[ 2.972677] USB Mass Storage support registered.
[ 2.972974] usb-storage: device found at 3
[ 2.972979] usb-storage: waiting for device to settle before scanning
[ 3.031725] Floppy drive(s): fd0 is 1.44M
[ 3.080866] FDC 0 is a post-1991 82077
[ 3.120096] usb 5-2: new low speed USB device using uhci_hcd and address 2
[ 3.177377] sata_via 0000:00:0f.0: version 2.4
[ 3.177407] sata_via 0000:00:0f.0: PCI INT B -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20
[ 3.177467] sata_via 0000:00:0f.0: routed to hard irq line 11
[ 3.177670] Linux agpgart interface v0.103
[ 3.192218] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 3.195600] scsi1 : sata_via
[ 3.201317] scsi2 : sata_via
[ 3.203589] ata1: SATA max UDMA/133 cmd 0xf800 ctl 0xf400 bmdma 0xe800 irq 20
[ 3.203593] ata2: SATA max UDMA/133 cmd 0xf000 ctl 0xec00 bmdma 0xe808 irq 20
[ 3.203828] pata_via 0000:00:0f.1: version 0.3.4
[ 3.203856] pata_via 0000:00:0f.1: PCI INT A -> Link[ALKA] -> GSI 20 (level, low) -> IRQ 20
[ 3.213976] scsi3 : pata_via
[ 3.219377] scsi4 : pata_via
[ 3.221675] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xe000 irq 14
[ 3.221680] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xe008 irq 15
[ 3.221973] agpgart: Detected VIA VT3314 chipset
[ 3.314581] agpgart-via 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 3.314627] 8139cp 0000:00:07.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 3.316485] [drm] Initialized drm 1.1.0 20060810
[ 3.323105] usb 5-2: configuration #1 chosen from 1 choice
[ 3.408039] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 3.420686] ata3.00: ATA-6: WDC WD1200SB-01KBA0, 08.02D08, max UDMA/100
[ 3.420690] ata3.00: 234441648 sectors, multi 16: LBA48
[ 3.437654] ata3.00: configured for UDMA/100
[ 3.620026] ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 3.631136] scsi 3:0:0:0: Direct-Access ATA WDC WD1200SB-01K 08.0 PQ: 0 ANSI: 5
[ 3.631449] sd 3:0:0:0: Attached scsi generic sg0 type 0
[ 3.632206] sd 3:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 3.632299] sd 3:0:0:0: [sda] Write Protect is off
[ 3.632304] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.632348] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.632664] sda: sda1 sda2 < sda5 >
[ 3.670059] sd 3:0:0:0: [sda] Attached SCSI disk
[ 3.815372] usbcore: registered new interface driver hiddev
[ 3.836962] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:10.3/usb5/5-2/5-2:1.0/input/input5
[ 3.837580] generic-usb 0003:046D:C045.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:10.3-2/input0
[ 3.837649] usbcore: registered new interface driver usbhid
[ 3.837901] usbhid: v2.6:USB HID core driver
[ 3.837953] 8139too Fast Ethernet driver 0.9.28
[ 3.838019] 8139too 0000:00:07.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 3.839343] eth0: RealTek RTL8139 at 0xfc00, 00:13:d3:ea:ea:26, IRQ 20
[ 3.880538] alloc irq_desc for 16 on node -1
[ 3.880543] alloc kstat_irqs on node -1
[ 3.880553] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.885111] [drm] nouveau 0000:01:00.0: Detected an NV30 generation card (0x034600b1)
[ 3.885225] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PROM
[ 4.015093] [drm] nouveau 0000:01:00.0: ... appears to be valid
[ 4.015221] [drm] nouveau 0000:01:00.0: BMP BIOS found
[ 4.015225] [drm] nouveau 0000:01:00.0: BMP version 5.40
[ 4.015228] [drm] nouveau 0000:01:00.0: Bios version 04.34.20.69
[ 4.015232] [drm] nouveau 0000:01:00.0: Found Display Configuration Block version 2.2
[ 4.015237] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 01000300 000088b8
[ 4.015241] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 02020321 00000303
[ 4.015337] [drm] nouveau 0000:01:00.0: Loading NV17 power sequencing microcode
[ 4.015340] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xEC5F
[ 4.028030] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xEEFA
[ 4.028041] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xF040
[ 4.028078] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xF1C9
[ 4.028083] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xF1E6
[ 4.028088] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 5 at offset 0xF203
[ 4.036024] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 6 at offset 0xF39C
[ 4.046432] [TTM] Zone kernel: Available graphics memory: 437764 kiB.
[ 4.046437] [TTM] Zone highmem: Available graphics memory: 1030120 kiB.
[ 4.046457] [drm] nouveau 0000:01:00.0: 256 MiB VRAM
[ 4.046529] agpgart-via 0000:00:00.0: AGP 3.5 bridge
[ 4.046549] agpgart: modprobe tried to set rate=x12. Setting to AGP3 x8 mode.
[ 4.046559] agpgart-via 0000:00:00.0: putting AGP V3 device into 8x mode
[ 4.046641] nouveau 0000:01:00.0: putting AGP V3 device into 8x mode
[ 4.046646] [drm] nouveau 0000:01:00.0: 256 MiB GART (aperture)
[ 4.046971] [drm] nouveau 0000:01:00.0: Allocating FIFO number 0
[ 4.047849] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised FIFO 0
[ 4.047863] [drm] nouveau 0000:01:00.0: Initial CRTC_OWNER is 0
[ 4.047870] [drm] nouveau 0000:01:00.0: Saving VGA fonts
[ 4.089837] [drm] nouveau 0000:01:00.0: Detected a VGA connector
[ 4.090169] [drm] nouveau 0000:01:00.0: Detected a TV connector
[ 4.091467] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
[ 4.091473] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV encoder (output 1)
[ 4.213083] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 4.724253] [drm] nouveau 0000:01:00.0: allocated 1440x900 fb: 0x49000, bo f6f0e800
[ 4.724572] fb0: nouveaufb frame buffer device
[ 4.724576] registered panic notifier
[ 4.724589] [drm] Initialized nouveau 0.0.15 20090420 for 0000:01:00.0 on minor 0
[ 4.729829] vga16fb: initializing
[ 4.729840] vga16fb: mapped to 0xc00a0000
[ 4.729848] vga16fb: not registering due to another framebuffer present
[ 4.769017] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on vga encoder (output 0)
[ 4.769026] [drm] nouveau 0000:01:00.0: Output VGA-1 is running on CRTC 0 using output A
[ 4.774836] Console: switching to colour frame buffer device 180x56
[ 5.124265] xor: automatically using best checksumming function: pIII_sse
[ 5.144009] pIII_sse : 4703.000 MB/sec
[ 5.144012] xor: using function: pIII_sse (4703.000 MB/sec)
[ 5.155024] device-mapper: dm-raid45: initialized v0.2594b
[ 5.300880] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 7.972276] usb-storage: device scan complete
[ 7.973122] scsi 0:0:0:0: CD-ROM ATAPI iHAS120 6 7L0F PQ: 0 ANSI: 0
[ 7.977123] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 7.977160] Uniform CD-ROM driver Revision: 3.20
[ 7.979152] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 7.982287] sr 0:0:0:0: Attached scsi generic sg1 type 5
[ 18.262859] Adding 4805624k swap on /dev/sda5. Priority:-1 extents:1 across:4805624k
[ 18.369756] udev: starting version 151
[ 18.755524] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 18.871611] type=1505 audit(1281564677.405:2): operation="profile_load" pid=449 name="/sbin/dhclient3"
[ 18.913862] type=1505 audit(1281564677.449:3): operation="profile_load" pid=449 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 18.914241] type=1505 audit(1281564677.449:4): operation="profile_load" pid=449 name="/usr/lib/connman/scripts/dhclient-script"
[ 18.938974] lp: driver loaded but no devices found
[ 18.963680] type=1505 audit(1281564677.497:5): operation="profile_load" pid=508 name="/usr/sbin/ntpd"
[ 18.995652] parport_pc 00:0a: reported by Plug and Play ACPI
[ 18.995713] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 19.088356] lp0: using parport0 (interrupt-driven).
[ 19.553839] ppdev: user-space parallel port driver
[ 19.568463] cfg80211: Calling CRDA to update world regulatory domain
[ 19.745405] cfg80211: World regulatory domain updated:
[ 19.745412] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 19.745416] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.745420] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.745423] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.745426] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.745429] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 20.388471] phy0: Selected rate control algorithm 'minstrel'
[ 20.389513] Registered led device: rt2800usb-phy0::radio
[ 20.389547] Registered led device: rt2800usb-phy0::assoc
[ 20.389579] Registered led device: rt2800usb-phy0::quality
[ 20.390798] usbcore: registered new interface driver rt2800usb
[ 20.441890] rt2870sta: module is from the staging directory, the quality is unknown, you have been warned.
[ 20.481959] rtusb init --->
[ 20.482189] usbcore: registered new interface driver rt2870
[ 20.520212] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 20.551179] udev: renamed network interface wlan0 to wlan1
[ 20.580693] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 20.690128] rt2800usb 1-3:1.0: firmware: requesting rt2870.bin
[ 20.719273] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[ 20.719284] alloc irq_desc for 22 on node -1
[ 20.719287] alloc kstat_irqs on node -1
[ 20.719299] VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22
[ 20.719477] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[ 20.892944] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 20.898503] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 20.898511] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 20.898514] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 21.034749] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 21.328161] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 22.016679] type=1505 audit(1281564680.553:6): operation="profile_load" pid=940 name="/usr/share/gdm/guest-session/Xsession"
[ 22.020819] type=1505 audit(1281564680.557:7): operation="profile_replace" pid=941 name="/sbin/dhclient3"
[ 22.021528] type=1505 audit(1281564680.557:8): operation="profile_replace" pid=941 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 22.021924] type=1505 audit(1281564680.557:9): operation="profile_replace" pid=941 name="/usr/lib/connman/scripts/dhclient-script"
[ 22.038905] type=1505 audit(1281564680.573:10): operation="profile_load" pid=942 name="/usr/bin/evince"
[ 22.057025] type=1505 audit(1281564680.593:11): operation="profile_load" pid=942 name="/usr/bin/evince-previewer"
[ 22.277663] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 23.251610] [drm] nouveau 0000:01:00.0: Allocating FIFO number 1
[ 23.255348] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised FIFO 1
[ 26.194933] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 27.119236] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 27.732464] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 28.402510] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 29.016220] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 29.662677] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 31.152040] eth0: no IPv6 routers present
[ 34.174944] wlan1: deauthenticating from 00:15:05:d6:3f:22 by local choice (reason=3)
[ 34.180531] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 34.182575] wlan1: direct probe responded
[ 34.182583] wlan1: authenticate with AP 00:15:05:d6:3f:22 (try 1)
[ 34.184228] wlan1: authenticated
[ 34.184276] wlan1: associate with AP 00:15:05:d6:3f:22 (try 1)
[ 34.186689] wlan1: RX AssocResp from 00:15:05:d6:3f:22 (capab=0x461 status=0 aid=3)
[ 34.186696] wlan1: associated
[ 34.195090] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 36.186654] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 38.919328] nouveau 0000:01:00.0: The number of extension(32) is over max (4), actually read number (4)
[ 44.492902] wlan1: deauthenticating from 00:15:05:d6:3f:22 by local choice (reason=3)
[ 44.556040] wlan1: no IPv6 routers present
[ 49.079093] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 49.080484] ISOFS: changing to secondary root
[ 83.568616] wlan1: deauthenticating from 00:15:05:d6:3f:22 by local choice (reason=3)
[ 83.780871] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 83.784415] wlan1: direct probe responded
[ 83.784423] wlan1: authenticate with AP 00:15:05:d6:3f:22 (try 1)
[ 83.788913] wlan1: authenticated
[ 83.789192] wlan1: associate with AP 00:15:05:d6:3f:22 (try 1)
[ 83.791280] wlan1: RX AssocResp from 00:15:05:d6:3f:22 (capab=0x461 status=0 aid=3)
[ 83.791287] wlan1: associated
[ 94.482673] wlan1: deauthenticating from 00:15:05:d6:3f:22 by local choice (reason=3)
[ 746.728571] wlan1: deauthenticating from 00:15:05:d6:3f:22 by local choice (reason=3)
[ 746.946456] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 747.144031] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 747.344024] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 747.544021] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 753.043470] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 753.240179] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 753.440188] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 753.640257] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 870.238775] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 870.437157] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 870.636033] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 870.836023] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 876.542822] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 876.740035] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 876.940036] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 877.140034] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 907.534681] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 907.732039] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 907.932026] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 908.132027] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 913.846699] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 914.044040] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 914.244042] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 914.444041] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 920.182707] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 920.380038] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 920.580036] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 920.780066] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 923.023930] usb 1-3: USB disconnect, address 2
[ 923.064013] phy0 -> rt2800usb_wait_wpdma_ready: Error - WPDMA TX/RX busy, aborting.
[ 923.066990] __ratelimit: 21 callbacks suppressed
[ 923.066997] NetworkManager[717]: segfault at 3c ip b72ff617 sp bfec73ec error 4 in libnl.so.1.1[b72e0000+42000]
[ 933.652036] usb 1-3: new high speed USB device using ehci_hcd and address 5
[ 933.804485] usb 1-3: configuration #1 chosen from 1 choice
[ 933.847022] phy1: Selected rate control algorithm 'minstrel'
[ 933.852945] Registered led device: rt2800usb-phy1::radio
[ 933.854046] Registered led device: rt2800usb-phy1::assoc
[ 933.857057] Registered led device: rt2800usb-phy1::quality
[ 933.883349] udev: renamed network interface wlan0 to wlan1
[ 933.885959] rt2800usb 1-3:1.0: firmware: requesting rt2870.bin
[ 934.117675] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[ 946.475278] wlan1: deauthenticating from 00:15:05:d6:3f:22 by local choice (reason=3)
[ 946.481010] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 946.484561] wlan1: direct probe responded
[ 946.484569] wlan1: authenticate with AP 00:15:05:d6:3f:22 (try 1)
[ 946.486179] wlan1: authenticated
[ 946.486229] wlan1: associate with AP 00:15:05:d6:3f:22 (try 1)
[ 946.488206] wlan1: RX AssocResp from 00:15:05:d6:3f:22 (capab=0x461 status=0 aid=3)
[ 946.488212] wlan1: associated
[ 946.496949] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 956.516023] wlan1: no IPv6 routers present
[ 1143.420076] No probe response from AP 00:15:05:d6:3f:22 after 500ms, disconnecting.
[ 1144.849629] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 1145.048028] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 1145.248028] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 1145.448051] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 1151.186673] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 1151.384069] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 1151.584050] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 1151.784048] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 1157.499602] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 1157.696038] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 1157.896098] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 1158.096062] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 1160.190833] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 1160.388047] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 1160.588040] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 1160.788070] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 1166.498716] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 1166.696184] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 1166.896020] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 1167.096032] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
[ 1172.811271] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 1)
[ 1173.008055] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 2)
[ 1173.208078] wlan1: direct probe to AP 00:15:05:d6:3f:22 (try 3)
[ 1173.408071] wlan1: direct probe to AP 00:15:05:d6:3f:22 timed out
elizabeth@elizabeth-desktop:~$
MotherBoard Asrock Alive NF7G-HD720p Rev5.0 NVIDIA® GeForce 7050 / nForce 630A MCP Chipsets
XFX ATI Radeon HD 4350 1 GB Graphics Card HD435XZAH2
Disabled Integrated NVIDIA® GeForce7 Series (NV44) DX9.0 VGA, Pixel Shader 3.0, Max. shared memory 256MB
NVIDIA® PureVideo™ Ready
RAM Mushkin Enhanced Blackline 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400)
CPU AMD Athlon 64 X2 5000+ Brisbane 2.6GHz Socket AM2 65W Dual-Core Black Edition Processor Model ADO5000DSWOF
HARDDRIVE Western Digital Caviar Blue WD5000AAJS 500GB 7200 RPM SATA 3.0Gb/s
OS UE2.5 64 bit
OS UE2.6 64 bit